Showing posts with label Market. Show all posts
Showing posts with label Market. Show all posts

Tuesday, March 11, 2014

March 10, Return to Garaha Larh, Lost in the Bush again.

Monday morning we returned to Garaha Larh. This was project is both training and water project. We were just going to install the new pump, test both pumps, show the chairman of the local water committee how to test the pump and have him change the seals on a pump piston.

Yakubu, Adams, and I drove across the Benue River and picked up Ruebin part way up the hill. There we also picked up some small breakfast cakes. A women was frying the small cakes in oil over an open fire along the road. These were made with corn flour and tossed in a mixture of spices. They were pretty good and plenty greasy.

Today we have the new Toyota Hilux. It is a gasoline powered small heavy duty 4 wheel drive truck. The last trip we drove the old diesel powered Hilux (I think it is a 1989 or early 1990s). It is a Lazarus truck. I has come back from the dead more than once. It has seen a lot of hard miles on bush roads. The old truck is not as bad as many vehicles on the road. Diesel here is expensive and is not subsidized.

Gasoline is subsidized and is relatively cheap (less than 95 Naira per liter about $2.15 a gallon). The problem is that to get the subsidized rate you have to go to the National Petroleum station. Currently, there is a gas crisis. The lines at the National Petroleum Station in Jimeta is close to a mile long at most times. The commercial gas stations in Jimeta rarely have fuel. They sell fuel at a little above the subsidized price. All of their signs say 95 Naira but if they have fuel they will charge you 110 to 130 Naira per liter during normal times and 160 or more now.

We start our trip at 7:30 AM with the fuel gauge between 1/8 and empty. There are stations open across the Benue. The closest ones charge around 160 Naria per liter. We went past the University and past a few open stations and went in to a small station that was charging 140 Naira. 10.000 Naira purchased 71.4 liters almost filled the tank

We made our third stop at the next larger village. This stop was for fried yams and Suya. These are snacks we can eat as we drive. Suya are small pieces of  meat or to be more precise I would say meat trimmings, that have been cooked over a fire and rolled in a combinations of spices. If I had not been driving I would have taken a few pictures. These are the normal stops that are made on trips like this. Last week we were late and we drove without food.

We made good time until after Gombi, The two Military checkpoints after Gombi were long. There had been an attack north of Gombi over the weekend. It is not known if it was Boko Haram or another group that had a conflict with the village.  A couple churches were burned and people were killed. Garaha ares is calm. We made it to Hong in 2 1/2 hours from Jimeta. We stopped there to get bleach to disinfect the borehole and a notebook to give to the water chairman to record his pump tests results. It was market day in Hong and the highway along the main street was already filled with vendors. We drove past the market and Adams got out and walked back to the market area.

Google Earth View of Garaha Area. 

Lost in the bush again. Last trip we got on the wrong trail after Garaha and went to the village of Dabna to the southwest of Garaha Lar and followed a motorcyle trail back to Garaha Larh. This trip we stopped and asked directions in Garaha. We got on the correct road but we had to leave the road because of a collaped bridge. As we came up out of the dry stream bed on the north side of the bridfe we took the road to the right. It is a little hard to see from where we emerged but there are three roads. The far left road goes to Dabna, the center road goes to Garaha Larh and the right road goes to Garagha Dutse. Dutse means Rock. Garaha Dutse is beside a large granite hill. I got my camera out to take a picture and to use its built in GPS to see which way it was to Garaha Lahr. The memory card was in my computer back in Jimeta. It had the previous pictures and coordinates of Garaha Larh.

In Garaha Dutse we asked directions. With a lot of hand waving a farmer told us the directions. Off we went as we left the village we saw a man at a pump I suggested we confirm the directions. Adams and Yakubu said no we should turn right on the bigger of two trails. The hand waving I remembered was around the rock and left. Two of our crew were native Kilba and this being Kilba Land I had to follow what they told me. After about 10 minutes later they said to turn around. We went back and found took the smaller trail. This may have been the first time a 4 wheeled vehicle had taken this route. It was a single rut trail. After a while we came to some women working in a field. We asked an older lady resting under a tree if we were on the trail to Graaha Larh. She said yes we were on the right trail and there were no more corners (as interpreted). I gave her two thumbs up and a double handed wave.

We arrived in the village and found out the Chairman was gone to Hong for market day. We found the other young men that had helped us on the last trip and the village chief. As the young men unloaded the pipes, tank and pump head from the truck, I got out the weighted tape measure and checked the depth to the water (6 meters) and the depth  to the bottom on the borehole. Adams had reported that the driller had bored to 23 meter. My first indication was that the bottom was at 19 meters. We added a second weight (bolt) to the tape measure. The casing was not exactly vertical and the tape was sticking to the side of the casing making it hard to probe for the bottom. We decided to only put on 5 pipes. The bottom of the hole is somewhere between 17 and 23 meters. I initial reading was 19 meters. The bottom of the cylinder, inlet will be at 15 meters. The static water level was found to be 6 meters the pump inlet will be in 9 meters of water (29.5 feet) and at least 2 meters above the bottom.

Pipes & tank installed connecting piston to operation rod
After we installed the pump a man pump and pumped until we filled the 2 1/2 inch riser pipe and got the water flowing. We (we meaning Adams and Yakubu in Kilba) were discussing with the chief and some of the men some of the things to do to keep the area clean and to maintain the pump, when someone said the water had stopped. We looked at the outlet and no water was flowing. Then we realized that man who had been pumping the handle got tired and stopped.

The pipes we had bought in Jimeta for this pump were used. Jimeta has many of these used pipes. Many of the pump mechanics in this area are only used to the Mark III. When they are called fix a Mark III they convert them into Mark II and sell the pipes in the market. They do not know that you do not need to remove the riser pipe to replace the piston seals.They remove the 65 mm PVC pipes and open top cylinders and replace it with the 32 mm steel pipes and closed top cylinders. Almost almost all of the 65 mm pipes I saw in the market have missing gaskets (we would call them O-Rings). Without these the joints leak. We used teflon plumbers tape and still had a little leakage. The leak test of the pump is to stop pumping for 5 minutes. Then count how many pump stokes it takes to get water. With this pump it took less than three. This is considered in the good range. More than 10 strokes is considered time for repair.
First Water from new borehole.

After testing the new pump we went back to the pump we repaired last week. At noon there was a line of buckets waiting their turn to be filled. The people were waiting under the shade of trees. In a village with adequate water supply they will have finished the morning fetching of water by this time. In the evening as the temperature cools the lines will form again. In villages without adequate water the will pump all day and late into the night. This overuse of the pump quickly wears out the seals in the cylinders.

Line for water at pump at noon. 
This pump had its original 65 mm PVC pipes with the seals. When we tested it for leakage by stopping pumping for 5 minutes, the water resumed with the first stroke. This pump has very little leakage.

In Kilba land and some other places they install used tires to the back of pump.This seems to give them a bounce and also prevents the pump handle from hitting the pump head. I have seen pump handles and pump heads that are bent from years of banging.

While waiting the 5 minutes for the leakage test I decided to take a picture fromt the pump handle prospective. I used the widest angle that my camera had and exaggerate the length of the handle. Ruebin is the man on the left, Adams in the center and Yakubu on the right.

Click to enlarge.
We returned by the direct route to Garaha and on to Hong. Yakubu had some bringing him a package in Hong so we stopped and waited. After a while the man showed up with a bag stuffed with a fried peanut cake. Sticks of fried peanut residue from peanut oil extraction. It is used in a lot of dishes or to make these sticks little treats.

At the check point near Pella there were people selling mangos, onions, and other things. They were asking 300 Naria for a bowl of around 12 mangos. Adams talked them down to 200 Naira ($1.20). In Jimeta they would cost more. Adams, Yakubu and I both bought a bowl each. Ruebin bought 2 bowls and 2 bowls of onions. About half way to Jimeta my eyes started to water from the onion smell.

We arrived back in Jimeta at 5:30. The trip was about 10 hours total. After we unloaded I gave Adams a ride up to the transport area by the Main Market and drove to Luka's Memorial Market (small store). Luka has good prices and the widest variety of goods. I found some fruit cocktail in fruit juice, peach halves, peach slices in grape juice, sardines in tomato sauce and a variety of other things that I will eat over the next six weeks. My pantry is now full.

Peanut cakes.
I hope there are not to many errors in this posting. the network is slow so I am going to post it and edit out errors later. Most of it has been read twice. I always find errors. Even if I proof read it 4 or 5 times. Yes there were a lot if errors. I hope it is a little better now. I am finding that the only good internet time is early in the morning. By 10 AM the network becomes overloaded.


Mangos from Pella.

Pantry of food.










Sunday, March 9, 2014

Saturday March 9, Walk to Market, Wedding and Buying Pump.


Saturday March 8, 2014


Saturday, I woke up at 3 AM when the power came on and noticed that the internet was running. It has been trouble during the weekday. I had several emails that I had tried to send but had failed many times. So I got up and sent out emails and Face Book messages and posted some pictures on Face Book. I got back to bed before sun up and slept in until after 9 AM.

Late morning I started to walked to the main Market to buy some parboiled rice (about a mile one way). Yakubu Market had wanted 1200 Naira ($7.12) for a 2 pound bag of Uncle Ben's. I was not willing to pay that much.

A wedding had completed at the Cathedral and the reception party was underway on the compound next to the Cathedral. The house I live in while I visit here is in the North East corner of the compound. The Deaf Centre is in the North West corner. Most weekends in March, April and May they will have a wedding reception on the compound. Last year we had three on the same Saturday.


I stopped at the wedding and took a couple pictures. The wedding was well attended. The groom is a doctor. I climbed up the spiral staircase to the balcony exit of the Cathedral to get good view. The wedding always publishes the color theme. Women will find matching fabric and will make dresses and head scarves to attend the wedding. I noticed a lot of women had the same pink and grey fabric made into a variety of dress styles. Then I spotted a three men chatting up some ladies with trousers and matching ties made of the same material. I asked one of the men to strike a pose

Click to enlarge
I headed on up the main road to the Jimeta Main Market. It is about a mile walk. Along the way I saw a man with a pull cart hauling a heavy bed. These movers earn little money for hard work. The picture does not show it but the street is a slight upward incline. The man was moving faster than I was walking. There a quite a few of these going along with and sometimes against traffic. Boys also push loads in wheelbarrows. There are boys throughout the market waiting for someone to buy something they need taken out to their cars or back to their homes.

Route to Market
At the market, I walked up and down up and down several rows of stalls before I found a man selling rice by the measure. Most had 5 kilo or 50 kilogram bags. He wants 600 Naira for the small measure of what he called parboiled, but the bag it was in did not say parboiled.. This is more than I was willing to pay. He told me 500 and that I would not find it any cheaper at any other shop. I continued on through several more rows of shops. I noticed shop with large container of what I thought might be dried mushrooms. I continued on and did not find much. Lot of shops with about anything you could need. Mostly made in China, Nigeria or England.
One of many aisles of shops.

I circled back to where I saw what looked like mushrooms and noticed he had rice in a bag labeled parboiled from Thailand. I asked him the price and he said 350 Naira for the small measure. I agreed and I got about 3 pound for $2.07. I have not yet boiled any to see what it taste like. I looked around his shop and purchased salt, dried peppers, flavored drink mixes, tomato paste in small packets and a few other things. The dried mushroom turned out to be sliced dried ginger. I bought a 30 Naira bag ($0.18).  I hope I remember where he was located he was a nice young man.
Items outside of one of the tiny shops

Closer view of main market.
The main market was under construction when I first came to Nigeria in 2006. I am told that the first contractor took a lot of money and disappeared. The second contractor was not a lot better. I believe it was open on my 2010 trip. Each of the little metal buildings have shops on both sides. Each shop is about 3 meters deep (10 feet). The smallest shops are only 3m X 3m. The biggest I saw was probably 3m X 9m. Most have their merchandise extended out past the curb and into the traffic area. These small aisles can be maneuvered by boys with wheelbarrows. There are a few wide aisle where car can move through. The storm drains were poorly constructed and many covers have collapsed. Besides shops there are money exchanges and restaurants. On the west end is an open meat market. I have pictures of it in previous blogs.

Later in the evening I walked up to the Plumbing pipe market area. It is only about 1/2 mile south of the Cathedral on Hospital Road and met Bulama to pick up the pipes, rods and pumps we will need Monday to finish the work at Garaha Larh. The materials originally ordered for this project was the wrong type of pump. He said he had the correct material and all was new. We are going to install an India Mark III pump. Their other pump is a Mark III. This pump is considered a Village Level Operator Maintenance (VLOM) pump. The main parts that need to be replaced in hand pumps are worn out seals on the pump piston. A VLOM pump can have its piston removed without removing the riser pipes. The main pump used here is the India Mark II which is not VLOM. It has 1-1/4 inch steel riser pipes. The rise pipes filled with water have to be lifted out of the borehole. This is a complicated and somewhat dangerous operation. It takes skilled pump mechanics.

The India Mark III uses 2-1/2 inch PVC pipes. The ones recommended by the Nigerian Government have stainless steel screw on fittings. Only used screw on PVC pipes are available in Yola. They are manufactured in Lagos so they should be available there. The piston is about 2 inches in diameter. After removing the pump head and disconnection the operating chain from the operating rods the piston can be removed by lifting out the operating rods. The 3 to 4 hour task on a Mark II is less than an hour on a Mark III and few tools are needed. There is another pump called the Afridev that uses the same riser pipes but they made every bolt the pump the same size. It is even easier to change the seals. We are exploring the options to have these pumps available in Yola.

After getting the piston to the house/office I inspected the piston and found it to be used also. I will bring along all the repair parts and have the Water Committee Chairman in the village replace the parts. We will also be training him on how to perform weekly checks of the pump.